Elektron-Users

Midi Implementation Virus TI (CC List)

A JPG file containing 16 labeled boxes, for you to write in pattern info as a reference for performing live on the machinedrum and monomachine.

Elektron Machinedrum SPS-1 UserWave Software Editor - Mac Version

Elektron Machinedrum SPS-1 UserWave Software Editor - Windows version

As requested, the pattern and kit sysex for my reverse-engineered version of Autechre's LCC.

MD/MnM MKII Bracket - Left hand side.

(32) RANDOM CC SENDER by FINLAY SHAKESPEARE at FUTURE SOUND SYSTEMS:

Installation:
Simply copy and paste the contents of this zip file into a desired
folder and run Random CC.exe. The Random CC.dll file is the actual
VST plug-in for use in your sequencing software. You can copy and
paste this to your plug-ins folder.

Thanks to David Haupt for his CV to MIDI CC module.

www.futuresoundsystems.tk

www.myspace.com/futureimagefutureimage

Hi all,

 This is a firmware i wrote for the Ruin & Wesen mini command for external control of Octatrack FX, as well as porting the Wesen Supatrigga functionality from his MD Live sketch. See notes below.

cheers,

Tyrone

 

//  OT Live Sketch

// Note - this sketch assumes that you have:
//    RAM RECORDER machine on OT Track 5.  From memory I think you need to set the length to be 32 steps / 2 bars long.
//    MD running through a THRU machine on OT Track 6
//    MNM running through a THRU machine on OT Track 7
//    Filter FX assigned to FX block 1 on the THRU and RAM RECORDER machines
//    DJ EQ FX assigned to FX block 2 on the THRU and RAM RECORDER machines
//

// Notes on Variables:  update midi channels below for your setup if required
#define RECORDER_MIDI_CHANNEL (5 - 1)  // OT Track / Midi Channel 5
#define MD_THRU_MIDI_CHANNEL (6 - 1)  // OT Track / Midi Channel 6
#define MNM_THRU_MIDI_CHANNEL (7 - 1) // OT Track / Midi Channel 7
#define TETRA_MIDI_CHANNEL (12 - 1) // Midi Channel 12
#define CC_FX_1_PARAM_1 34  //FILTER BASE
#define CC_FX_1_PARAM_2 35  //FILTER WIDTH
#define CC_FX_2_PARAM_4 43  //EQ LOW GAIN
#define CC_FX_2_PARAM_6 45  //EQ HI GAIN
#define CC_PLAYBACK_PARAM_2 17  //RECORDER START
#define CC_PLAYBACK_PARAM_4 19  //RECORDER RATE

// General Notes - Firmware has two main "modes": 
// 1.0  Mode 1 - "THRU" machine mode.  Give control of FX on THRU machines. 
// 1.01 There are two pages in "THRU" machine mode.  To toggle between the two pages, press button 1 (top left) when in "THRU" machine mode.
// 1.1  Page 1 - DJEq Page - control of Low and Hi EQ for "MD THRU" and "MNM THRU"
// 1.11 Pressing an Encoder will "cut" the EQ to 0 or toggle it back to its previous value.  An asterix is displayed next to the encoder name to show when EQ "cut" is active
// 1.12 Holding Button 2 (bottom left) and pressing an encoder will restore the EQ back to 64 and disable "cut" mode
// 1.2  Page 2 - Filter Page - control of Filter Cutoffs for "MD THRU" and "MNM THRU"
// 1.21 Pressing an Encoder will "cut" the cutoff to 0 (BAS) or 127 (WDT), or toggle it back to its previous value.  An asterix is displayed next to the encoder name to show when EQ "cut" is active
// 1.22 Holding Button 2 (bottom left) and pressing an encoder will restore the cutoff back to 0 (BAS) or 127 (WDT) and disable "cut" mode
// 2.0  Mode 2 - "RAM RECORDER" mode.  Give control of FX on RAM RECORDER machine.
// 2.01 There is only one page for this mode which controls both the DJ EQ and Filter FX.
// 2.02 Functionality is same as above for fx controls
// 3.0  To switch from "THRU" to "RAM RECORD" mode, press button 4 (top right). 
// 3.1  To switch from "RAM RECORD" to "THRU" mode, press button 1 (top left).  Once back in "THRU" mode, subsequent presses of button 1 will switch between the two pages of "THRU" mode
// 4.0  Press button three to activate the wesen supatrigga functionality for the RAM RECORDER machine.  This can be activated from any mode/page.

 

 

4 ch dedicate to Ableton live ( Level-Filter-Send A-Send B ) with Ableton template inclusive and 4 ch dedicate to Sps-1 ( Level-LFO amount-Rev send-Delay send )

 

This is a Ableton Live Max4Live basic MIDI patch for the Monomachine.

All 56 Midi CC synth settings are accessalbe and sequencable. Seperated by 7 "Tabbed" pages in the same order as the MnM.
Unfortunitly Max4Live is required for you to use this patch in Ableton.

i was playing with the MD sysex at work today and made this Cubase user panel. It will give you a graphic user interface on screen from within Cubase that will allow you to adjust the parameters of the four FX Master machines. Have Fun!

A bash script to create evenly spaced sample chains using sox

Version 0.6 (updated 9.6.2013)

trimpad takes a set of samples and creates evenly spaced (sample accurate) sample chains, which allow for easy slicing in the Octatrack.

Also see this forum thread:  http://elektron-users.com/index.php?option=com_fireboard&Itemid=28&func=view&id=155708&catid=9